
Bole EKH Series
DESCRIPTION | UNIT | BL90EKH/C220 | ||||
International Specification | 220 | |||||
Screw Specification | A | B | C | D | ||
Screw diameter | mm | 25 | 28 | 32 | 38 | |
Screw ratio | 23 | 23 | 20 | 18 | ||
Theroretical injection capacity | cm3 | 79 | 98 | 129 | 181 | |
Shot weight (PS) | g | 72 | 91 | 118 | 167 | |
oz | 2.6 | 3.2 | 4.2 | 5.9 | ||
Max. injection rate into Air | cm3/s | 79 | 99 | 130 | 183 | |
Max. injection rate into Air | g/s | 72 | 90 | 118 | 167 | |
Injection pressure | Mpa | 290 | 231 | 177 | 125 | |
Theoretical plasticizing speed | g/s (PS) | 8 | 11 | 16 | 26 | |
Injection stroke | mm | 160 | ||||
Max. injection speed | mm/s | 162 | ||||
Max. screw speed | r/min | 331 | ||||
Sys. Pressure | Mpa | 17.5 | ||||
Pump motor (min~max) | kW | 8.9~15 | ||||
Number of Motors | pc | 1 | ||||
Pre-plasticizing motor power | kW | OPTIONAL | ||||
Heater power | kW | 5.4 | ||||
Number of temp. control zons | 3+1 | |||||
Clamping force | kN | 900 | ||||
opening stroke | mm | 320 | ||||
Space between tie bar | mm x mm | 355×325 | ||||
Min. mould height | mm | 125 | ||||
Max. mould height | mm | 360 | ||||
Max Daylight | mm | 680 | ||||
Ejector stroke | mm | 70 | ||||
Ejector force forward | kN | 34 | ||||
Ejector force back | kN | 22 | ||||
Number of ejector bar | PC | 5 | ||||
Dry cycle time | s | 2.9 | ||||
Energy consumption | kW.h/kg | ≤0.4 (1) | ||||
Hopper capacity | kg | 25 | ||||
Oil tank capacity | L | 120 | ||||
Machine dimensions (LxWxH) | m x m x m | 4.2×1.3×2.1 | ||||
Machine weight | ton | 2.5 |
DESCRIPTION | UNIT | BL120EKH/C360 | |||
---|---|---|---|---|---|
International Specification | 360 | ||||
Screw Specification | A | B | C | D | |
Screw diameter | mm | 32 | 36 | 40 | 45 |
Screw ratio | 23 | 22 | 20 | 18 | |
Theroretical injection capacity | cm3 | 153 | 193 | 239 | 302 |
Shot weight (PS) | g | 141 | 178 | 220 | 278 |
oz | 5.0 | 6.3 | 7.8 | 9.8 | |
Max. injection rate into Air | cm3/s | 96 | 122 | 150 | 190 |
Max. injection rate into Air | g/s | 87 | 111 | 137 | 173 |
Injection pressure | Mpa | 239 | 189 | 153 | 121 |
Theoretical plasticizing speed | g/s (PS) | 11 | 14 | 19 | 27 |
Injection stroke | mm | 190 | |||
Max. injection speed | mm/s | 119 | |||
Max. screw speed | r/min | 221 | |||
Sys. Pressure | Mpa | 17.5 | |||
Pump motor (min~max) | kW | 8.9~15 | |||
Number of Motors | pc | | | |||
Pre-plasticizing motor power | kW | OPTIONAL | |||
Heater power | kW | 6.8 | |||
Number of temp. control zons | 3+1 | ||||
Clamping force | kN | 1200 | |||
opening stroke | mm | 360 | |||
Space between tie bar | mm x mm | 4.5×355 | |||
Min. mould height | mm | 160(125) | |||
Max. mould height | mm | 430(430) | |||
Max Daylight | mm | 790(790) | |||
Ejector stroke | mm | 120 | |||
Ejector force forward | kN | 34 | |||
Ejector force back | kN | 22 | |||
Number of ejector bar | PC | 5 | |||
Dry cycle time | s | 3.1 | |||
Energy consumption | kW.h/kg | ≤0.4 (1) | |||
Hopper capacity | kg | 25 | |||
Oil tank capacity | L | 150 | |||
Machine dimensions (LxWxH) | m x m x m | 4.4×1.3×2.1 | |||
Machine weight | ton | 3.3 |
DESCRIPTION | UNIT | BL160EKH/C490 | |||
International Specification | 490 | ||||
Screw Specification | A | B | C | D | |
Screw diameter | mm | 36 | 40 | 45 | 50 |
Screw ratio | 23 | 23 | 21 | 18 | |
Theroretical injection capacity | cm3 | 214 | 264 | 334 | 412 |
Shot weight (PS) | g | 197 | 243 | 307 | 379 |
oz | 6.9 | 8.6 | 10.9 | 13.4 | |
Max. injection rate into Air | cm3/s | 127 | 156 | 198 | 244 |
Max. injection rate into Air | g/s | 115 | 142 | 180 | 222 |
Injection pressure | Mpa | 230 | 186 | 147 | 119 |
Theoretical plasticizing speed | g/s (PS) | 16 | 21 | 29 | 38 |
Injection stroke | mm | 210 | |||
Max. injection speed | mm/s | 125 | |||
Max. screw speed | r/min | 240 | |||
Sys. Pressure | Mpa | 17.5 | |||
Pump motor (min~max) | kW | 13.7~18.7 | |||
Number of Motors | pc | | | |||
Pre-plasticizing motor power | kW | OPTIONAL | |||
Heater power | kW | 9.5 | |||
Number of temp. control zons | 3+1 | ||||
Clamping force | kN | 1600 | |||
opening stroke | mm | 420 | |||
Space between tie bar | mm x mm | 455×405 | |||
Min. mould height | mm | 180(145) | |||
Max. mould height | mm | 500(500) | |||
Max Daylight | mm | 920(920) | |||
Ejector stroke | mm | 140 | |||
Ejector force forward | kN | 49 | |||
Ejector force back | kN | 37 | |||
Number of ejector bar | PC | 5 | |||
Dry cycle time | s | 2.4 | |||
Energy consumption | kW.h/kg | ≤0.4 (1) | |||
Hopper capacity | kg | 25 | |||
Oil tank capacity | L | 165 | |||
Machine dimensions (LxWxH) | m x m x m | 4.9x.3×2.1 | |||
Machine weight | ton | 4 |
DESCRIPTION | UNIT | BL200EKH/C700 | |||
---|---|---|---|---|---|
International Specification | 700 | ||||
Screw Specification | A | B | C | D | |
Screw diameter | mm | 40 | 45 | 50 | 55 |
Screw ratio | 23 | 22 | 20 | 18 | |
Theroretical injection capacity | cm3 | 301 | 382 | 471 | 570 |
Shot weight (PS) | g | 277 | 351 | 433 | 524 |
oz | 9.8 | 12.4 | 15.3 | 18.5 | |
Max. injection rate into Air | cm3/s | 155 | 197 | 243 | 294 |
Max. injection rate into Air | g/s | 141 | 179 | 221 | 267 |
Injection pressure | Mpa | 235 | 185 | 150 | 124 |
Theoretical plasticizing speed | g/s (PS) | 18 | 25 | 33 | 41 |
Injection stroke | mm | 240 | |||
Max. injection speed | mm/s | 124 | |||
Max. screw speed | r/min | 210 | |||
Sys. Pressure | Mpa | 17.5 | |||
Pump motor (min~max) | kW | 16.4~23 | |||
Number of Motors | pc | I | |||
Pre-plasticizing motor power | kW | OPTIONAL | |||
Heater power | kW | 12.7 | |||
Number of temp. control zons | 3+1 | ||||
Clamping force | kN | 2000 | |||
opening stroke | mm | 480 | |||
Space between tie bar | mm x mm | 505*505 | |||
Min. mould height | mm | 200(165) | |||
Max. mould height | mm | 530(530) | |||
Max Daylight | mm | 1010(1010) | |||
Ejector stroke | mm | 150 | |||
Ejector force forward | kN | 49 | |||
Ejector force back | kN | 37 | |||
Number of ejector bar | PC | 5 | |||
Dry cycle time | s | 2.5 | |||
Energy consumption | kW.h/kg | ≤0.4 (1) | |||
Hopper capacity | kg | 25 | |||
Oil tank capacity | L | 230 | |||
Machine dimensions (LxWxH) | m x m x m | 5.2*1.4*2.2 | |||
Machine weight | ton | 5.5 |
DESCRIPTION | UNIT | BL250EKH/C980 | |||
---|---|---|---|---|---|
International Specification | 700 | ||||
Screw Specification | A | B | C | D | |
Screw diameter | mm | 45 | 50 | 55 | 60 |
Screw ratio | 23 | 23 | 21 | 19 | |
Theroretical injection capacity | cm3 | 429 | 530 | 641 | 763 |
Shot weight (PS) | g | 395 | 487 | 590 | 702 |
oz | 14.0 | 17.2 | 20.8 | 24.8 | |
Max. injection rate into Air | cm3/s | 200 | 247 | 299 | 355 |
Max. injection rate into Air | g/s | 182 | 225 | 272 | 323 |
Injection pressure | Mpa | 230 | 186 | 154 | 129 |
Theoretical plasticizing speed | g/s (PS) | 27 | 35 | 43 | 58 |
Injection stroke | mm | 270 | |||
Max. injection speed | mm/s | 126 | |||
Max. screw speed | r/min | 221 | |||
Sys. Pressure | Mpa | 17.5 | |||
Pump motor (min~max) | kW | 20.5~27.8 | |||
Number of Motors | pc | I | |||
Pre-plasticizing motor power | kW | OPTIONAL | |||
Heater power | kW | 14.52 | |||
Number of temp. control zons | 3+1 | ||||
Clamping force | kN | 2500 | |||
opening stroke | mm | 530 | |||
Space between tie bar | mm x mm | 555X505 | |||
Min. mould height | mm | 220(175) | |||
Max. mould height | mm | 570(570) | |||
Max Daylight | mm | 1100(1100) | |||
Ejector stroke | mm | 150 | |||
Ejector force forward | kN | 67 | |||
Ejector force back | kN | 39 | |||
Number of ejector bar | PC | 9 | |||
Dry cycle time | s | 3.3 | |||
Energy consumption | kW.h/kg | ≤0.4 (1) | |||
Hopper capacity | kg | 50 | |||
Oil tank capacity | L | 280 | |||
Machine dimensions (LxWxH) | m x m x m | 5.7X1.5X2.4 | |||
Machine weight | ton | 7 |
DESCRIPTION | UNIT | BL300EKH/C1600 | |||
---|---|---|---|---|---|
International Specification | 1600 | ||||
Screw Specification | A | B | C | D | |
Screw diameter | mm | 55 | 60 | 65 | 70 |
Screw ratio | 23 | 23 | 21 | 20 | |
Theroretical injection capacity | cm3 | 748 | 890 | 1045 | 1212 |
Shot weight (PS) | g | 688 | 819 | 961 | 1115 |
oz | 24.3 | 28.9 | 34.0 | 39.4 | |
Max. injection rate into Air | cm3/s | 267 | 317 | 373 | 432 |
Max. injection rate into Air | g/s | 243 | 289 | 339 | 393 |
Injection pressure | Mpa | 219 | 184 | 157 | 135 |
Theoretical plasticizing speed | g/s (PS) | 41 | 55 | 69 | 84 |
Injection stroke | mm | 315 | |||
Max. injection speed | mm/s | 112 | |||
Max. screw speed | r/min | 210 | |||
Sys. Pressure | Mpa | 17.5 | |||
Pump motor (min~max) | kW | 26.7~36.5 | |||
Number of Motors | pc | I | |||
Pre-plasticizing motor power | kW | optional | |||
Heater power | kW | 19.55 | |||
Number of temp. control zons | 4+1 | ||||
Clamping force | kN | 3000 | |||
opening stroke | mm | 590 | |||
Space between tie bar | mm x mm | 655×605 | |||
Min. mould height | mm | 250 (205) | |||
Max. mould height | mm | 660 (660) | |||
Max Daylight | mm | 1250 (1250) | |||
Ejector stroke | mm | 190 | |||
Ejector force forward | kN | 67 | |||
Ejector force back | kN | 39 | |||
Number of ejector bar | PC | 13 | |||
Dry cycle time | s | 2.8 | |||
Energy consumption | kW.h/kg | ≤1.4 (1Level) | |||
Hopper capacity | kg | 50 | |||
Oil tank capacity | L | 350 | |||
Machine dimensions (LxWxH) | m x m x m | 6.3×1.7×2.5 | |||
Machine weight | ton | 9 |
DESCRIPTION | UNIT | BL400EKH/C2400 | |||
---|---|---|---|---|---|
International Specification | 2400 | ||||
Screw Specification | A | B | C | D | |
Screw diameter | mm | 62 | 68 | 75 | 80 |
Screw ratio | 23 | 23 | 21 | 20 | |
Theroretical injection capacity | cm3 | 1086 | 1307 | 1590 | 1809 |
Shot weight (PS) | g | 999 | 1202 | 1462 | 1664 |
oz | 35.3 | 42.5 | 51.7 | 58.8 | |
Max. injection rate into Air | cm3/s | 334 | 401 | 488 | 556 |
Max. injection rate into Air | g/s | 304 | 365 | 444 | 506 |
Injection pressure | Mpa | 219 | 182 | 149 | 131 |
Theoretical plasticizing speed | g/s (PS) | 47 | 59 | 85 | 100 |
Injection stroke | mm | 360 | |||
Max. injection speed | mm/s | III | |||
Max. screw speed | r/min | 175 | |||
Sys. Pressure | Mpa | 17.5 | |||
Pump motor (min~max) | kW | 39.7~40.9 | |||
Number of Motors | pc | I | |||
Pre-plasticizing motor power | kW | optional | |||
Heater power | kW | 24.05 | |||
Number of temp. control zons | 4+1 | ||||
Clamping force | kN | 4000 | |||
opening stroke | mm | 660 | |||
Space between tie bar | mm x mm | 710×660 | |||
Min. mould height | mm | 270 (225) | |||
Max. mould height | mm | 710 (710) | |||
Max Daylight | mm | 1370 (1370) | |||
Ejector stroke | mm | 190 | |||
Ejector force forward | kN | 123 | |||
Ejector force back | kN | 82 | |||
Number of ejector bar | PC | 13 | |||
Dry cycle time | s | 3.6 | |||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |||
Hopper capacity | kg | 50 | |||
Oil tank capacity | L | 420 | |||
Machine dimensions (LxWxH) | m x m x m | 7×1.8×2.5 | |||
Machine weight | ton | 12.2 |
DESCRIPTION | UNIT | BL450EKH/C3100 | ||
---|---|---|---|---|
International Specification | 3100 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 70 | 75 | 85 |
Screw ratio | 23 | 21 | 19 | |
Theroretical injection capacity | cm3 | 1462 | 1678 | 2155 |
Shot weight (PS) | g | 1345 | 1544 | 1983 |
oz | 47.5 | 54.5 | 70.1 | |
Max. injection rate into Air | cm3/s | 430 | 493 | 634 |
Max. injection rate into Air | g/s | 391 | 449 | 576 |
Injection pressure | Mpa | 212 | 185 | 144 |
Theoretical plasticizing speed | g/s (PS) | 66 | 79 | 101 |
Injection stroke | mm | 380 | ||
Max. injection speed | mm/s | 112 | ||
Max. screw speed | r/min | 164 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 50.7~52.7 | ||
Number of Motors | pc | I | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 27.35 | ||
Number of temp. control zons | 4+1 | |||
Clamping force | kN | 4500 | ||
opening stroke | mm | 750 | ||
Space between tie bar | mm x mm | 760X710 | ||
Min. mould height | mm | 330 | ||
Max. mould height | mm | 780 | ||
Max Daylight | mm | 1530 | ||
Ejector stroke | mm | 210 | ||
Ejector force forward | kN | 123 | ||
Ejector force back | kN | 82 | ||
Number of ejector bar | PC | 13 | ||
Dry cycle time | s | 3.7 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 50 | ||
Oil tank capacity | L | 420 | ||
Machine dimensions (LxWxH) | m x m x m | 7.7X1.9×2.6 | ||
Machine weight | ton | 14.5 |
DESCRIPTION | UNIT | BL530EKH/C4000 | ||
---|---|---|---|---|
International Specification | 4000 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 75 | 80 | 90 |
Screw ratio | 22 | 21 | 19 | |
Theroretical injection capacity | cm3 | 1943 | 2211 | 2798 |
Shot weight (PS) | g | 1787 | 2034 | 2574 |
oz | 63.2 | 71.9 | 91.0 | |
Max. injection rate into Air | cm3/s | 523 | 595 | 753 |
Max. injection rate into Air | g/s | 476 | 542 | 686 |
Injection pressure | Mpa | 209 | 184 | 145 |
Theoretical plasticizing speed | g/s (PS) | 76 | 90 | 124 |
Injection stroke | mm | 440 | ||
Max. injection speed | mm/s | 118 | ||
Max. screw speed | r/min | 158 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 57.3~62.7 | ||
Number of Motors | pc | 2 | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 32 | ||
Number of temp. control zons | 3+1 | |||
Clamping force | kN | 5300 | ||
opening stroke | mm | 850 | ||
Space between tie bar | mm x mm | 860X800 | ||
Min. mould height | mm | 330 | ||
Max. mould height | mm | 850 | ||
Max Daylight | mm | 1700 | ||
Ejector stroke | mm | 210 | ||
Ejector force forward | kN | 123 | ||
Ejector force back | kN | 82 | ||
Number of ejector bar | PC | 13 | ||
Dry cycle time | s | 4.3 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 100 | ||
Oil tank capacity | L | 600 | ||
Machine dimensions (LxWxH) | m x m x m | 8.3X2.1X2.9 | ||
Machine weight | ton | 19.5 |
DESCRIPTION | UNIT | BL600EKH/C4700 | ||
---|---|---|---|---|
International Specification | 4700 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 80 | 90 | 100 |
Screw ratio | 24 | 21 | 19 | |
Theroretical injection capacity | cm3 | 2286 | 2893 | 3572 |
Shot weight (PS) | g | 2103 | 2662 | 3286 |
oz | 74.3 | 94.1 | 116.1 | |
Max. injection rate into Air | cm3/s | 619 | 783 | 967 |
Max. injection rate into Air | g/s | 563 | 713 | 880 |
Injection pressure | Mpa | 206 | 163 | 132 |
Theoretical plasticizing speed | g/s (PS) | 88 | 121 | 155 |
Injection stroke | mm | 455 | ||
Max. injection speed | mm/s | 123 | ||
Max. screw speed | r/min | 153 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 67.1~75.7 | ||
Number of Motors | pc | 2 | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 36.1 | ||
Number of temp. control zons | 5+1 | |||
Clamping force | kN | 6000 | ||
opening stroke | mm | 900 | ||
Space between tie bar | mm x mm | 910X855 | ||
Min. mould height | mm | 380 | ||
Max. mould height | mm | 910 | ||
Max Daylight | mm | 1810 | ||
Ejector stroke | mm | 220 | ||
Ejector force forward | kN | 123 | ||
Ejector force back | kN | 82 | ||
Number of ejector bar | PC | 21 | ||
Dry cycle time | s | 4.4 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 100 | ||
Oil tank capacity | L | 750 | ||
Machine dimensions (LxWxH) | m x m x m | 9.1X2.2X2.9 | ||
Machine weight | ton | 22 |
DESCRIPTION | UNIT | BL700EKH/C5800 | ||
---|---|---|---|---|
International Specification | 5800 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 85 | 95 | 105 |
Screw ratio | 23 | 21 | 19 | |
Theroretical injection capacity | cm3 | 2836 | 3542 | 4327 |
Shot weight (PS) | g | 2609 | 3259 | 3981 |
oz | 92.2 | 115.2 | 140.7 | |
Max. injection rate into Air | cm3/s | 708 | 884 | 1080 |
Max. injection rate into Air | g/s | 644 | 805 | 983 |
Injection pressure | Mpa | 206 | 165 | 135 |
Theoretical plasticizing speed | g/s (PS) | 92 | 132 | 177 |
Injection stroke | mm | 500 | ||
Max. injection speed | mm/s | 125 | ||
Max. screw speed | r/min | 150 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 79.4~81.8 | ||
Number of Motors | pc | 2 | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 43 | ||
Number of temp. control zons | 5+1 | |||
Clamping force | kN | 7000 | ||
opening stroke | mm | 970 | ||
Space between tie bar | mm x mm | 955×855 | ||
Min. mould height | mm | 400 | ||
Max. mould height | mm | 960 | ||
Max Daylight | mm | 1930 | ||
Ejector stroke | mm | 260 | ||
Ejector force forward | kN | 166 | ||
Ejector force back | kN | 117 | ||
Number of ejector bar | PC | 21 | ||
Dry cycle time | s | 3.8 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 100 | ||
Oil tank capacity | L | 900 | ||
Machine dimensions (LxWxH) | m x m x m | 9.6×2.3×3 | ||
Machine weight | ton | 25 |
DESCRIPTION | UNIT | BL800EKH/C8600 | ||
---|---|---|---|---|
International Specification | 8600 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 95 | 105 | 115 |
Screw ratio | 23 | 21 | 19 | |
Theroretical injection capacity | cm3 | 3861 | 4717 | 5658 |
Shot weight (PS) | g | 3552 | 4339 | 5205 |
oz | 12.5 | 153.3 | 183.9 | |
Max. injection rate into Air | cm3/s | 734 | 897 | 1076 |
Max. injection rate into Air | g/s | 668 | 816 | 979 |
Injection pressure | Mpa | 223 | 183 | 152 |
Theoretical plasticizing speed | g/s (PS) | 134 | 180 | 231 |
Injection stroke | mm | 545 | ||
Max. injection speed | mm/s | 104 | ||
Max. screw speed | r/min | 152 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 91.6~92.4 | ||
Number of Motors | pc | 2 | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 50.1 | ||
Number of temp. control zons | 5+1 | |||
Clamping force | kN | 8000 | ||
opening stroke | mm | 1050 | ||
Space between tie bar | mm x mm | 1055×955 | ||
Min. mould height | mm | 450 | ||
Max. mould height | mm | 1000 | ||
Max Daylight | mm | 2050 | ||
Ejector stroke | mm | 270 | ||
Ejector force forward | kN | 166 | ||
Ejector force back | kN | 117 | ||
Number of ejector bar | PC | 21 | ||
Dry cycle time | s | 5.6 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 100 | ||
Oil tank capacity | L | 1070 | ||
Machine dimensions (LxWxH) | m x m x m | 10.4×2.5×3.1 | ||
Machine weight | ton | 30 |
DESCRIPTION | UNIT | BL900EKH/C8600 | ||
---|---|---|---|---|
International Specification | 8600 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 100 | 110 | 120 |
Screw ratio | 230 | 21 | 19 | |
Theroretical injection capacity | cm3 | 4278 | 5177 | 6161 |
Shot weight (PS) | g | 3936 | 4763 | 5668 |
oz | 139.1 | 168.3 | 200.3 | |
Max. injection rate into Air | cm3/s | 814 | 985 | 1172 |
Max. injection rate into Air | g/s | 741 | 896 | 1066 |
Injection pressure | Mpa | 202 | 167 | 140 |
Theoretical plasticizing speed | g/s (PS) | 154 | 207 | 263 |
Injection stroke | mm | 545 | ||
Max. injection speed | mm/s | 104 | ||
Max. screw speed | r/min | 152 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 91.6~92.4 | ||
Number of Motors | pc | 2 | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 53 | ||
Number of temp. control zons | 5+1 | |||
Clamping force | kN | 9000 | ||
opening stroke | mm | 1120 | ||
Space between tie bar | mm x mm | 1110×1010 | ||
Min. mould height | mm | 450 | ||
Max. mould height | mm | 1100 | ||
Max Daylight | mm | 2220 | ||
Ejector stroke | mm | 300 | ||
Ejector force forward | kN | 232 | ||
Ejector force back | kN | 132 | ||
Number of ejector bar | PC | 21 | ||
Dry cycle time | s | 5.6 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 100 | ||
Oil tank capacity | L | 1070 | ||
Machine dimensions (LxWxH) | m x m x m | 10.8×2.6×3.1 | ||
Machine weight | ton | 38 |
DESCRIPTION | UNIT | BL1000EKH/C10500 | ||
---|---|---|---|---|
International Specification | 10500 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 110 | 120 | 130 |
Screw ratio | 23 | 21 | 19 | |
Theroretical injection capacity | cm3 | 5652 | 6726 | 7894 |
Shot weight (PS) | g | 5199 | 6188 | 7262 |
oz | 183.7 | 218.7 | 256.6 | |
Max. injection rate into Air | cm3/s | 985 | 1172 | 1375 |
Max. injection rate into Air | g/s | 896 | 1066 | 1252 |
Injection pressure | Mpa | 185 | 156 | 133 |
Theoretical plasticizing speed | g/s (PS) | 166 | 211 | 248 |
Injection stroke | mm | 595 | ||
Max. injection speed | mm/s | 104 | ||
Max. screw speed | r/min | 122 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 101.4~105.4 | ||
Number of Motors | pc | 2 | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 56.2 | ||
Number of temp. control zons | 6+1 | |||
Clamping force | kN | 10000 | ||
opening stroke | mm | 1150 | ||
Space between tie bar | mm x mm | 1160×1060 | ||
Min. mould height | mm | 480 | ||
Max. mould height | mm | 1160 | ||
Max Daylight | mm | 2310 | ||
Ejector stroke | mm | 300 | ||
Ejector force forward | kN | 248 | ||
Ejector force back | kN | 165 | ||
Number of ejector bar | PC | 21 | ||
Dry cycle time | s | 7 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 100 | ||
Oil tank capacity | L | 1350 | ||
Machine dimensions (LxWxH) | m x m x m | 10.9×2.9×4.2 | ||
Machine weight | ton | 45 |
DESCRIPTION | UNIT | BL1200EKH/C10500 | ||
---|---|---|---|---|
International Specification | 10500 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 110 | 120 | 130 |
Screw ratio | 23 | 21 | 19 | |
Theroretical injection capacity | cm3 | 5652 | 6726 | 7894 |
Shot weight (PS) | g | 5199 | 6188 | 7262 |
oz | 183.7 | 218.7 | 256.6 | |
Max. injection rate into Air | cm3/s | 985 | 1172 | 1375 |
Max. injection rate into Air | g/s | 896 | 1066 | 1252 |
Injection pressure | Mpa | 185 | 156 | 133 |
Theoretical plasticizing speed | g/s (PS) | 166 | 211 | 248 |
Injection stroke | mm | 595 | ||
Max. injection speed | mm/s | 104 | ||
Max. screw speed | r/min | 122 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 101.4~105.4 | ||
Number of Motors | pc | 2 | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 56.2 | ||
Number of temp. control zons | 6+1 | |||
Clamping force | kN | 12000 | ||
opening stroke | mm | 1320 | ||
Space between tie bar | mm x mm | 1260×1120 | ||
Min. mould height | mm | 500 | ||
Max. mould height | mm | 1200 | ||
Max Daylight | mm | 2520 | ||
Ejector stroke | mm | 350 | ||
Ejector force forward | kN | 248 | ||
Ejector force back | kN | 165 | ||
Number of ejector bar | PC | 21 | ||
Dry cycle time | s | 8 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 200 | ||
Oil tank capacity | L | 1350 | ||
Machine dimensions (LxWxH) | m x m x m | 11.4x3x4.2 | ||
Machine weight | ton | 52 |
DESCRIPTION | UNIT | BL1400EKH/C13000 | ||
---|---|---|---|---|
International Specification | 13000 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 120 | 130 | 140 |
Screw ratio | 23 | 21 | 20 | |
Theroretical injection capacity | cm3 | 7235 | 8491 | 9847 |
Shot weight (PS) | g | 6656 | 7811 | 9059 |
oz | 235.2 | 276 | 320.1 | |
Max. injection rate into Air | cm3/s | 1210 | 1420 | 1647 |
Max. injection rate into Air | g/s | 1101 | 1292 | 1499 |
Injection pressure | Mpa | 181 | 154 | 133 |
Theoretical plasticizing speed | g/s (PS) | 201 | 237 | 284 |
Injection stroke | mm | 640 | ||
Max. injection speed | mm/s | 107 | ||
Max. screw speed | r/min | 117 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 119.1~122.7 | ||
Number of Motors | pc | 3 | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 74.6 | ||
Number of temp. control zons | 6+1 | |||
Clamping force | kN | 14000 | ||
opening stroke | mm | 1450 | ||
Space between tie bar | mm x mm | 1420X1220 | ||
Min. mould height | mm | 580 | ||
Max. mould height | mm | 1300 | ||
Max Daylight | mm | 2750 | ||
Ejector stroke | mm | 350 | ||
Ejector force forward | kN | 248 | ||
Ejector force back | kN | 165 | ||
Number of ejector bar | PC | 29 | ||
Dry cycle time | s | 8.5 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 200 | ||
Oil tank capacity | L | 1650 | ||
Machine dimensions (LxWxH) | m x m x m | 12.3X3.3X4.1 | ||
Machine weight | ton | 67 |
DESCRIPTION | UNIT | BL1600EKH/C16000 | ||
---|---|---|---|---|
International Specification | 16000 | |||
Screw Specification | A | B | C | |
Screw diameter | mm | 130 | 140 | 150 |
Screw ratio | 23 | 21 | 20 | |
Theroretical injection capacity | cm3 | 9021 | 10462 | 12011 |
Shot weight (PS) | g | 8300 | 9625 | 11050 |
oz | 293.3 | 340.1 | 390.4 | |
Max. injection rate into Air | cm3/s | 1420 | 1647 | 1891 |
Max. injection rate into Air | g/s | 1292 | 1499 | 1721 |
Injection pressure | Mpa | 180 | 155 | 135 |
Theoretical plasticizing speed | g/s (PS) | 220 | 264 | 326 |
Injection stroke | mm | 680 | ||
Max. injection speed | mm/s | 107 | ||
Max. screw speed | r/min | 108 | ||
Sys. Pressure | Mpa | 17.5 | ||
Pump motor (min~max) | kW | 142.3~145.1 | ||
Number of Motors | pc | 3 | ||
Pre-plasticizing motor power | kW | optional | ||
Heater power | kW | 79.9 | ||
Number of temp. control zons | 6+1 | |||
Clamping force | kN | 16000 | ||
opening stroke | mm | 1550 | ||
Space between tie bar | mm x mm | 1520X1320 | ||
Min. mould height | mm | 680 | ||
Max. mould height | mm | 1450 | ||
Max Daylight | mm | 3000 | ||
Ejector stroke | mm | 400 | ||
Ejector force forward | kN | 363 | ||
Ejector force back | kN | 280 | ||
Number of ejector bar | PC | 29 | ||
Dry cycle time | s | 9 | ||
Energy consumption | kW.h/kg | ≤0.4 (1Level) | ||
Hopper capacity | kg | 200 | ||
Oil tank capacity | L | 1650 | ||
Machine dimensions (LxWxH) | m x m x m | 13.4X3.4X4.3 | ||
Machine weight | ton | 90 |
DESCRIPTION | UNIT | BL1850EKH/C22000 | |
---|---|---|---|
International Specification | 22000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 140 | 160 |
Screw ratio | 24 | 21 | |
Theroretical injection capacity | cm3 | 14155 | 18488 |
Shot weight (PS) | g | 13023 | 17009 |
oz | 460.2 | 601 | |
Max. injection rate into Air | cm3/s | 1624 | 2121 |
Max. injection rate into Air | g/s | 1478 | 1930 |
Injection pressure | Mpa | 157 | 120 |
Theoretical plasticizing speed | g/s (PS) | 195 | 304 |
Injection stroke | mm | 920 | |
Max. injection speed | mm/s | 106 | |
Max. screw speed | r/min | 80 | |
Sys. Pressure | Mpa | 17.5 | |
Pump motor (min~max) | kW | 142.3~145.1 | |
Number of Motors | pc | 3 | |
Pre-plasticizing motor power | kW | 167 | |
Heater power | kW | 80 | |
Number of temp. control zons | 6+2 | ||
Clamping force | kN | 18500 | |
opening stroke | mm | 1680 | |
Space between tie bar | mm x mm | 1620X1420 | |
Min. mould height | mm | 750 | |
Max. mould height | mm | 1550 | |
Max Daylight | mm | 3230 | |
Ejector stroke | mm | 400 | |
Ejector force forward | kN | 363 | |
Ejector force back | kN | 280 | |
Number of ejector bar | PC | 29 | |
Dry cycle time | s | 10 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 200 | |
Oil tank capacity | L | 1650 | |
Machine dimensions (LxWxH) | m x m x m | 14.9X3.9X4.5 | |
Machine weight | ton | 105 |
DESCRIPTION | UNIT | BL1850EKH/C35000 | |
---|---|---|---|
International Specification | 35000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 160 | 180 |
Screw ratio | 23.6 | 21 | |
Theroretical injection capacity | cm3 | 22508 | 28486 |
Shot weight (PS) | g | 20707 | 26207 |
oz | 731.7 | 926 | |
Max. injection rate into Air | cm3/s | 2016 | 2551 |
Max. injection rate into Air | g/s | 1835 | 2322 |
Injection pressure | Mpa | 158 | 125 |
Theoretical plasticizing speed | g/s (PS) | 304 | 368 |
Injection stroke | mm | 1120 | |
Max. injection speed | mm/s | 100 | |
Max. screw speed | r/min | 80 | |
Sys. Pressure | Mpa | 17.5 | |
Pump motor (min~max) | kW | 172.6~185.9 | |
Number of Motors | pc | 4 | |
Pre-plasticizing motor power | kW | 167 | |
Heater power | kW | 95 | |
Number of temp. control zons | 7+1 | ||
Clamping force | kN | 18500 | |
opening stroke | mm | 1680 | |
Space between tie bar | mm x mm | 1620X1420 | |
Min. mould height | mm | 750 | |
Max. mould height | mm | 1550 | |
Max Daylight | mm | 3230 | |
Ejector stroke | mm | 400 | |
Ejector force forward | kN | 363 | |
Ejector force back | kN | 280 | |
Number of ejector bar | PC | 29 | |
Dry cycle time | s | 9.5 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 200 | |
Oil tank capacity | L | 1950 | |
Machine dimensions (LxWxH) | m x m x m | 15.8X3.9X4.6 | |
Machine weight | ton |
DESCRIPTION | UNIT | BL2200EKH/C35000 | |
---|---|---|---|
International Specification | 35000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 160 | 180 |
Screw ratio | 23.6 | 21 | |
Theroretical injection capacity | cm3 | 22508 | 28486 |
Shot weight (PS) | g | 20707 | 26207 |
oz | 731.7 | 926 | |
Max. injection rate into Air | cm3/s | 2016 | 2551 |
Max. injection rate into Air | g/s | 1835 | 2322 |
Injection pressure | Mpa | 158 | 125 |
Theoretical plasticizing speed | g/s (PS) | 304 | 368 |
Injection stroke | mm | 1120 | |
Max. injection speed | mm/s | 100 | |
Max. screw speed | r/min | 80 | |
Sys. Pressure | Mpa | 17.5 | |
Pump motor (min~max) | kW | 172.6~185.9 | |
Number of Motors | pc | 4 | |
Pre-plasticizing motor power | kW | 167 | |
Heater power | kW | 95 | |
Number of temp. control zons | 7+1 | ||
Clamping force | kN | 22000 | |
opening stroke | mm | 1850 | |
Space between tie bar | mm x mm | 1720X1520 | |
Min. mould height | mm | 750 | |
Max. mould height | mm | 1700 | |
Max Daylight | mm | 3550 | |
Ejector stroke | mm | 450 | |
Ejector force forward | kN | 465 | |
Ejector force back | kN | 365 | |
Number of ejector bar | PC | 33 | |
Dry cycle time | s | 11 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 400 | |
Oil tank capacity | L | 1950 | |
Machine dimensions (LxWxH) | m x m x m | 16.9X4.1X4.6 | |
Machine weight | ton | 130 |
DESCRIPTION | UNIT | BL2200EKH/C54000 | |
---|---|---|---|
International Specification | 54000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 190 | 210 |
Screw ratio | 23 | 21 | |
Theroretical injection capacity | cm3 | 36840 | 45004 |
Shot weight (PS) | g | 33893 | 41404 |
oz | 1197.6 | 1463 | |
Max. injection rate into Air | cm3/s | 2396 | 2894 |
Max. injection rate into Air | g/s | 215 | 2633 |
Injection pressure | Mpa | 146 | 120 |
Theoretical plasticizing speed | g/s (PS) | 345 | 441 |
Injection stroke | mm | 1300 | |
Max. injection speed | mm/s | 84 | |
Max. screw speed | r/min | 63 | |
Sys. Pressure | Mpa | 17.5 | |
Pump motor (min~max) | kW | 193~197.8 | |
Number of Motors | pc | 4 | |
Pre-plasticizing motor power | kW | 209 | |
Heater power | kW | 115 | |
Number of temp. control zons | 8+1 | ||
Clamping force | kN | 22000 | |
opening stroke | mm | 1850 | |
Space between tie bar | mm x mm | 1720X1520 | |
Min. mould height | mm | 750 | |
Max. mould height | mm | 1700 | |
Max Daylight | mm | 3550 | |
Ejector stroke | mm | 450 | |
Ejector force forward | kN | 465 | |
Ejector force back | kN | 365 | |
Number of ejector bar | PC | 33 | |
Dry cycle time | s | 10 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 400 | |
Oil tank capacity | L | 1950 | |
Machine dimensions (LxWxH) | m x m x m | 18.1X4.1X4.6 | |
Machine weight | ton | 140 |
DESCRIPTION | UNIT | BL2500EKH/C54000 | |
---|---|---|---|
International Specification | 54000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 190 | 210 |
Screw ratio | 23 | 21 | |
Theroretical injection capacity | cm3 | 36840 | 45004 |
Shot weight (PS) | g | 33893 | 41404 |
oz | 1197.6 | 1463 | |
Max. injection rate into Air | cm3/s | 2369 | 2894 |
Max. injection rate into Air | g/s | 2156 | 2633 |
Injection pressure | Mpa | 146 | 120 |
Theoretical plasticizing speed | g/s (PS) | 345 | 441 |
Injection stroke | mm | 1300 | |
Max. injection speed | mm/s | 84 | |
Max. screw speed | r/min | 63 | |
Sys. Pressure | Mpa | 17.5 | |
Pump motor (min~max) | kW | 193~197.8 | |
Number of Motors | pc | 4 | |
Pre-plasticizing motor power | kW | 209 | |
Heater power | kW | 115 | |
Number of temp. control zons | 8+1 | ||
Clamping force | kN | 25000 | |
opening stroke | mm | 2000 | |
Space between tie bar | mm x mm | 1820X1620 | |
Min. mould height | mm | 800 | |
Max. mould height | mm | 1800 | |
Max Daylight | mm | 3800 | |
Ejector stroke | mm | 500 | |
Ejector force forward | kN | 465 | |
Ejector force back | kN | 365 | |
Number of ejector bar | PC | 33 | |
Dry cycle time | s | 11 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 400 | |
Oil tank capacity | L | 1950 | |
Machine dimensions (LxWxH) | m x m x m | 18.6X4.3X4.8 | |
Machine weight | ton | 170 |
DESCRIPTION | UNIT | BL2800EKH/C54000 | |
---|---|---|---|
International Specification | 54000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 190 | 210 |
Screw ratio | 23 | 21 | |
Theroretical injection capacity | cm3 | 36840 | 45004 |
Shot weight (PS) | g | 33893 | 41404 |
oz | 1197.6 | 1463 | |
Max. injection rate into Air | cm3/s | 2369 | 2894 |
Max. injection rate into Air | g/s | 2156 | 2633 |
Injection pressure | Mpa | 146 | 120 |
Theoretical plasticizing speed | g/s (PS) | 345 | 441 |
Injection stroke | mm | 1300 | |
Max. injection speed | mm/s | 84 | |
Max. screw speed | r/min | 63 | |
Sys. Pressure | Mpa | 17.5 | |
Pump motor (min~max) | kW | 193~197.8 | |
Number of Motors | pc | 4 | |
Pre-plasticizing motor power | kW | 209 | |
Heater power | kW | 115 | |
Number of temp. control zons | 8+1 | ||
Clamping force | kN | 28000 | |
opening stroke | mm | 2100 | |
Space between tie bar | mm x mm | 1920X1720 | |
Min. mould height | mm | 850 | |
Max. mould height | mm | 1900 | |
Max Daylight | mm | 4000 | |
Ejector stroke | mm | 500 | |
Ejector force forward | kN | 465 | |
Ejector force back | kN | 365 | |
Number of ejector bar | PC | 33 | |
Dry cycle time | s | 12.5 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 200 | |
Oil tank capacity | L | 1950 | |
Machine dimensions (LxWxH) | m x m x m | 19.1X4.5X4.9 | |
Machine weight | ton | 190 |
DESCRIPTION | UNIT | BL2800EKH/C72000 | |
---|---|---|---|
International Specification | 72000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 215 | 240 |
Screw ratio | 23 | 20.5 | |
Theroretical injection capacity | cm3 | 49350 | 61494 |
Shot weight (PS) | g | 45402 | 56574 |
oz | 1604.3 | 1999.1 | |
Max. injection rate into Air | cm3/s | 2830 | 3526 |
Max. injection rate into Air | g/s | 2575 | 3208 |
Injection pressure | Mpa | 147 | 118 |
Theoretical plasticizing speed | g/s (PS) | 481 | 626 |
Injection stroke | mm | 1360 | |
Max. injection speed | mm/s | 78 | |
Max. screw speed | r/min | 63 | |
Sys. Pressure | Mpa | 17.3 | |
Pump motor (min~max) | kW | 202.8~210.8 | |
Number of Motors | pc | 4 | |
Pre-plasticizing motor power | kW | 314 | |
Heater power | kW | 233 | |
Number of temp. control zons | 8+1 | ||
Clamping force | kN | 28000 | |
opening stroke | mm | 2100 | |
Space between tie bar | mm x mm | 1920X1720 | |
Min. mould height | mm | 850 | |
Max. mould height | mm | 1900 | |
Max Daylight | mm | 4000 | |
Ejector stroke | mm | 500 | |
Ejector force forward | kN | 465 | |
Ejector force back | kN | 365 | |
Number of ejector bar | PC | 33 | |
Dry cycle time | s | 12 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 200 | |
Oil tank capacity | L | 2500 | |
Machine dimensions (LxWxH) | m x m x m | 20.1X4.5X5 | |
Machine weight | ton | 205 |
DESCRIPTION | UNIT | BL3300EKH/C72000 | |
---|---|---|---|
International Specification | 72000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 215 | 240 |
Screw ratio | 23 | 20.5 | |
Theroretical injection capacity | cm3 | 49350 | 61494 |
Shot weight (PS) | g | 45402 | 56574 |
oz | 1604.3 | 1999.1 | |
Max. injection rate into Air | cm3/s | 2830 | 3526 |
Max. injection rate into Air | g/s | 2575 | 3208 |
Injection pressure | Mpa | 147 | 118 |
Theoretical plasticizing speed | g/s (PS) | 481 | 626 |
Injection stroke | mm | 1360 | |
Max. injection speed | mm/s | 78 | |
Max. screw speed | r/min | 63 | |
Sys. Pressure | Mpa | 17.5 | |
Pump motor (min~max) | kW | 202.8~210.8 | |
Number of Motors | pc | 4 | |
Pre-plasticizing motor power | kW | 314 | |
Heater power | kW | 233 | |
Number of temp. control zons | 8+1 | ||
Clamping force | kN | 33000 | |
opening stroke | mm | 2200 | |
Space between tie bar | mm x mm | 2110×1910 | |
Min. mould height | mm | 950 | |
Max. mould height | mm | 2000 | |
Max Daylight | mm | 4200 | |
Ejector stroke | mm | 550 | |
Ejector force forward | kN | 618 | |
Ejector force back | kN | 483 | |
Number of ejector bar | PC | 25 | |
Dry cycle time | s | 13 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 400 | |
Oil tank capacity | L | 2500 | |
Machine dimensions (LxWxH) | m x m x m | 20.4x5x5.1 | |
Machine weight | ton | 255 |
DESCRIPTION | UNIT | BL3300EKH/C94000 | |
---|---|---|---|
International Specification | 94000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 240 | 260 |
Screw ratio | 23 | 21 | |
Theroretical injection capacity | cm3 | 64207 | 75354 |
Shot weight (PS) | g | 59070 | 69325 |
oz | 2087.3 | 2449.7 | |
Max. injection rate into Air | cm3/s | 3113 | 3654 |
Max. injection rate into Air | g/s | 2833 | 3325 |
Injection pressure | Mpa | 146 | 125 |
Theoretical plasticizing speed | g/s (PS) | 626 | 764 |
Injection stroke | mm | 1420 | |
Max. injection speed | mm/s | 69 | |
Max. screw speed | r/min | 63 | |
Sys. Pressure | Mpa | 17.5 | |
Pump motor (min~max) | kW | 253.5~263.5 | |
Number of Motors | pc | 5 | |
Pre-plasticizing motor power | kW | 314 | |
Heater power | kW | 233 | |
Number of temp. control zons | 8+1 | ||
Clamping force | kN | 33000 | |
opening stroke | mm | 2200 | |
Space between tie bar | mm x mm | 2110×1910 | |
Min. mould height | mm | 950 | |
Max. mould height | mm | 2000 | |
Max Daylight | mm | 4200 | |
Ejector stroke | mm | 550 | |
Ejector force forward | kN | 618 | |
Ejector force back | kN | 483 | |
Number of ejector bar | PC | 25 | |
Dry cycle time | s | 12.5 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 400 | |
Oil tank capacity | L | 3000 | |
Machine dimensions (LxWxH) | m x m x m | 21.2x5x5.1 | |
Machine weight | ton | 265 |
DESCRIPTION | UNIT | BL4000EKH/C94000 | |
International Specification | 94000 | ||
Screw Specification | A | B | |
Screw diameter | mm | 240 | 260 |
Screw ratio | 23 | 21 | |
Theroretical injection capacity | cm3 | 64207 | 75354 |
Shot weight (PS) | g | 59070 | 69325 |
oz | 2087.3 | 2449.7 | |
Max. injection rate into Air | cm3/s | 3113 | 3654 |
Max. injection rate into Air | g/s | 2833 | 3325 |
Injection pressure | Mpa | 146 | 125 |
Theoretical plasticizing speed | g/s (PS) | 626 | 764 |
Injection stroke | mm | 1420 | |
Max. injection speed | mm/s | 69 | |
Max. screw speed | r/min | 63 | |
Sys. Pressure | Mpa | 17.5 | |
Pump motor (min~max) | kW | 253.5~263.5 | |
Number of Motors | pc | 5 | |
Pre-plasticizing motor power | kW | 314 | |
Heater power | kW | 233 | |
Number of temp. control zons | 8+1 | ||
Clamping force | kN | 40000 | |
opening stroke | mm | 2350 | |
Space between tie bar | mm x mm | 2420×2220 | |
Min. mould height | mm | 1100 | |
Max. mould height | mm | 2100 | |
Max Daylight | mm | 4450 | |
Ejector stroke | mm | 600 | |
Ejector force forward | kN | 618 | |
Ejector force back | kN | 483 | |
Number of ejector bar | PC | 25 | |
Dry cycle time | s | 13.5 | |
Energy consumption | kW.h/kg | ≤0.4 (1Level) | |
Hopper capacity | kg | 400 | |
Oil tank capacity | L | 3000 | |
Machine dimensions (LxWxH) | m x m x m | 22.5×5.3×5.1 | |
Machine weight | ton | 320 |